Ten By Ten Custom Carbon Limited Edition EF parts

Post your For Sale threads here
User avatar
Jaime 91siB18
L5 - Built Motor
L5 - Built Motor
Posts: 1008
Joined: Sun Jun 15, 2008 7:21 am
Location: East Bay Area, NorCal. USA
Contact:

Ten By Ten Custom Carbon Limited Edition EF parts

Post by Jaime 91siB18 »

TEN BY TEN CUSTOM CARBON
http://www.TenByTenCustomCarbon.com
Genuine Carbon Fiber Rear Speaker Plates with Carbon Fiber bonded Fasteners
-Made to accomodate Rear Speakers on 88-91 Civic Hatchbacks that were not equipt from the Factory.
Image
Image
Image
Image
These Plates provide for a Super Clean, Flush-Mount, Show Quality Rear Speaker Set-Up, as opposed to those old bulky cheap plastic pods that are getting harder to find.
$125
Carbon Fiber Gauge Cluster Bezel Overlay (90-91 M.T. w/tach)
Image
Image
$75

FREE SHIPPING!!

Professional installation recomended, but not required.

MADE IN THE U.S.A.

We only use High Grade Epoxy resins for a clearer, more durable, stronger , and longer lasting part as compared to the use of the cheaper, inferior Polyester and vinyl ester resins.

Polyester and vinyl ester resins shrink up to 7% volumetrically and because the resin continues to cure over long periods of time this effect may not be immediately obvious. This cure accounts for the 'print through effect' observed on a lot of older polyester products.
-In comparison,
Epoxy Resins shrink less than 2% and an epoxy laminate will be a lot more stable and have better cosmetics over a long period of time than a polyester product.

--Other exciting parts in development.....
Last edited by Jaime 91siB18 on Tue Sep 28, 2010 3:37 pm, edited 2 times in total.

User avatar
Jaime 91siB18
L5 - Built Motor
L5 - Built Motor
Posts: 1008
Joined: Sun Jun 15, 2008 7:21 am
Location: East Bay Area, NorCal. USA
Contact:

Re: Ten By Ten Custom Carbon Limited Edition EF parts

Post by Jaime 91siB18 »

Image
Lower Cluster Surround
Image
Image
Image
Image
$65/Shipped

User avatar
Jaime 91siB18
L5 - Built Motor
L5 - Built Motor
Posts: 1008
Joined: Sun Jun 15, 2008 7:21 am
Location: East Bay Area, NorCal. USA
Contact:

Re: Ten By Ten Custom Carbon Limited Edition EF parts

Post by Jaime 91siB18 »

We'll be at the EF-vs-DA meet this weekend August 7th in Livermore California at Umigo indoor Kart track from 12-5pm
Hope to see you there...

popslovescivic
L2 - MPFI
L2 - MPFI
Posts: 192
Joined: Wed Sep 16, 2009 7:46 am

Re: Ten By Ten Custom Carbon Limited Edition EF parts

Post by popslovescivic »

Man I just love the look of those speaker plates. I wish you guys weren't so far away. That show's probably going to be fun. What is your current production level, do you have plenty in stock because I'll be getting some when $$$ permits.
Someday she's gonna be sweet, but for now she's just sassy

User avatar
91B16AHB
L5 - Built Motor
L5 - Built Motor
Posts: 1469
Joined: Mon Mar 30, 2009 8:26 pm
Location: Quinns NY

Re: Ten By Ten Custom Carbon Limited Edition EF parts

Post by 91B16AHB »

Crap...$125 shipped? That's the same if not less than OEM , if you can even find them, and btw I think look 100 times better.
Too bad my car has torn, stained, and burned DX seats and a competley stock interior inculing the original (non-working) stereo with the exception of a Si cluster, and ZERO carbon fiber...
would probably look pretty dumb in my car... ::)

User avatar
Jaime 91siB18
L5 - Built Motor
L5 - Built Motor
Posts: 1008
Joined: Sun Jun 15, 2008 7:21 am
Location: East Bay Area, NorCal. USA
Contact:

Re: Ten By Ten Custom Carbon Limited Edition EF parts

Post by Jaime 91siB18 »

popslovescivic wrote:Man I just love the look of those speaker plates. What is your current production level, do you have plenty in stock because I'll be getting some when $$$ permits.
Hey, Thanks for the comments.
We are a new Company that is constantly re-investing profits back into the company in the form of R&D and production of new parts. We have limited stock on hand. As for the Speaker Plates, we currently have only one set available for immediate shipment(as of 8/27/10) until our next production of a fresh sheet of that particular combination of materials. We have 3 lower dash trims ready to cut, and plenty of single layer twill carbon fiber sheets already made up for gauge bezels or whatever else you can come up with.
We just started production on molds for the 88-89 door/window pillar pieces and a interior center vent/clock delete for gauges or electronics. The Vent Delete should be ready in a week, the pillar pieces further out.
Lots of things on the drawing board as time and funding permit.
Stay tuned...

User avatar
Jaime 91siB18
L5 - Built Motor
L5 - Built Motor
Posts: 1008
Joined: Sun Jun 15, 2008 7:21 am
Location: East Bay Area, NorCal. USA
Contact:

Re: Ten By Ten Custom Carbon Limited Edition EF parts

Post by Jaime 91siB18 »


User avatar
Jaime 91siB18
L5 - Built Motor
L5 - Built Motor
Posts: 1008
Joined: Sun Jun 15, 2008 7:21 am
Location: East Bay Area, NorCal. USA
Contact:

Re: Ten By Ten Custom Carbon Limited Edition EF parts

Post by Jaime 91siB18 »

First two Vent Deletes, they are made in one peice. Obviously, they need to be cut out still. Look for pics, in the next day or so.
Image

User avatar
Jaime 91siB18
L5 - Built Motor
L5 - Built Motor
Posts: 1008
Joined: Sun Jun 15, 2008 7:21 am
Location: East Bay Area, NorCal. USA
Contact:

Re: Ten By Ten Custom Carbon Limited Edition EF parts

Post by Jaime 91siB18 »

Here are the first pics of the Center vent delete. These can be cut out to host a variation of different gauges and electronics.

Image
Image
Image
Image
Image

User avatar
Jaime 91siB18
L5 - Built Motor
L5 - Built Motor
Posts: 1008
Joined: Sun Jun 15, 2008 7:21 am
Location: East Bay Area, NorCal. USA
Contact:

Re: Ten By Ten Custom Carbon Limited Edition EF parts

Post by Jaime 91siB18 »

90-91 Civic Climate Control Delete.(88-89??, CRX??)
3mm
Image
$25

91EFbluehatch
L4 - Forced Induction
L4 - Forced Induction
Posts: 592
Joined: Tue Jan 26, 2010 6:34 pm

Re: Ten By Ten Custom Carbon Limited Edition EF parts

Post by 91EFbluehatch »

any chance of a carbon fiber rear hatch.
Image
91 CIVIC hatch. b16a2 in the works

User avatar
Jaime 91siB18
L5 - Built Motor
L5 - Built Motor
Posts: 1008
Joined: Sun Jun 15, 2008 7:21 am
Location: East Bay Area, NorCal. USA
Contact:

Re: Ten By Ten Custom Carbon Limited Edition EF parts

Post by Jaime 91siB18 »

Mounting Hardware
Image
Image
Image

Some fitting may be required via a small file at the contact points.

We just made the investment to soon move from the basic wet-layup method, to the much superior vacuum bagging technology. This produces the perfect resin/material ratio, and nearly blemish free parts.
stay tuned...

User avatar
el_jelly
L6 - Race Bred
L6 - Race Bred
Posts: 7549
Joined: Mon Dec 09, 2002 3:27 am
Location: Puerto Rico

Re: Ten By Ten Custom Carbon Limited Edition EF parts

Post by el_jelly »

So front/rear lips, side skirts, mirror covers, side moldings, front grill and other big parts are coming? 8) :D
IHeartMySTD wrote: We all know we like our women and cars with D's, not B's!!!! ;)
Where most of the questions are already answered > Engine swap guide, FAQs and Index thread

91EFbluehatch
L4 - Forced Induction
L4 - Forced Induction
Posts: 592
Joined: Tue Jan 26, 2010 6:34 pm

Re: Ten By Ten Custom Carbon Limited Edition EF parts

Post by 91EFbluehatch »

i would love to have a CF hatch.
Image
91 CIVIC hatch. b16a2 in the works

User avatar
Jaime 91siB18
L5 - Built Motor
L5 - Built Motor
Posts: 1008
Joined: Sun Jun 15, 2008 7:21 am
Location: East Bay Area, NorCal. USA
Contact:

Re: Ten By Ten Custom Carbon Limited Edition EF parts

Post by Jaime 91siB18 »

Right now we're just focused on refining our manufacturing process's. No hood, and hatches on the drawing board any time soon.
Infact, we just made the investment to soon move from the basic wet-layup method, to the much superior vacuum bagging technology. This produces the perfect resin/material ratio, and nearly blemish free parts.
stay tuned...

Radio Delete
Image

Post Reply